Continue doing daily layers of stain in the same way until you can no longer see streaks in the finish. I used a foam brush to apply a thick layer of the stain then used staining pads to wipe it off.
Apply the gel stain with a foam brush or pad then wipe the excess away after 30 seconds.
How to gel stain furniture. Im working with these doors propped up against my studio wall. Its very important to stir the gel stain. To prep the surface give it a quick wipe down with a fine-grit sandpaper.
You can apply it with a natural bristle brush foam brush or cotton rag this last one being my favorite way. Wipe down the furniture with a damp rag or tack cloth to remove any sanding residue. Gel stain is particularly forgiving with splotch-prone woods like birch cherry maple and pine.
HOW TO APPLY THE GEL STAIN Once youve decided on a color open the can and give it a good stir. This makeover was completed using all Dixie Belle paint products. Carpet may discolor if cleaned with mineral spirits.
Because gel stain is so much thicker than traditional wood stains its also very easy to apply. Once the area has dried recoat with gel stain and wipe off within the proper timeframe. Gel stain can be used on both laminate furniture and wood veneers.
How do I apply a gel stain. How to Use Gel Stain. These varieties tend to absorb thin traditional stains unevenly looking messy and unfinished no.
Do be sure to wear gloves because the stain will get all over your hands. If you are applying it in layers and not wiping away you will want to apply it similarly to how you would apply a poly product. To Sand to raw wood use th e coarser grit first like 80-100 then use about 180 to 220 to finish sand.
Using a shop towel applicator pad chip brush or lint-free rag apply the gel stain working in manageable areas. Start off by cleaning and sanding the surface. In all of my experiences Ive had to apply 3-4 coats of gel stain.
Let it dry and then lightly sand again. Apply On Wipe Off Method. Then wipe the surface with a damp cloth to remove any dust.
Using a cheap foam brush start painting the gel stain in the direction of the grain. Using a stir stick thoroughly stir the stain until well blended. Then you are ready to stain.
The best thing about gel stain is that you DO NOT have to completely sand your piece of furniture before you apply your stain. Follow along while we makeover some wood furniture. To scuff sand for preparation for gel stain use anywhere from a 150 to 220 grit.
Then brush on a water-based polyurethane with a foam brush. Sand or dust prevents the gel from adhering. My least favorite way to use gel stains.
If it looks like a gloopy mess thats perfect. Open your can of gel stain. Saturate a cleaning rag with the Clean Slate and rub over the surface of the furniture turning the side of the rag to pick up the grime.
Open the can of gel stain and mix with a paint stirrer until you get a nice creamy consistency. It took about 4 passes of wiping off the stain with a clean area on the staining pad to get all of the. The color of the furniture may darken temporarily from the Clean Slate.
First be sure to stir the gel stain well. As I mentioned before I used General Finishes Gel Stain in Java. Let it dry for 15 minutes.
You can also opt to stain the entire piece. The tooth grips the gel and allows it to adhere. Staining with the gel stains over existing finishes 4 different ways 1.
Option 1 is to sand to raw wood finish if you prefer. The excess gel stain should come up easily. My favorite Gel Stain General Finishes Gel stain is the perfect gel stain if you are wanting a flawless finish.
Then wipe the surface with a damp cloth to remove any dust. Step by step process of painting and using gel stain. If you have gel stain that has started to get tacky before you were able to wipe it off dip a rag in mineral spirits and apply a little bit to the problem area.
I love two tone MCM furniture. How to Apply a Clear Coat to Gel Stain. Always go with the grain with applying gel stain.
Can you thin gel stain. I also spray painted the metal bases at this point. Sand the surface very lightly with a paper bag or very high grit sandpaper 400 and then wipe off any sanding dust with a damp rag.
Option 2 is to scuff sand the existing finish if you are not sanding to raw wood. To prep the surface give it a quick wipe down with a fine-grit sandpaper. Once the stain is completely dry apply a gel stain top coat to lock in the color and protect the finish.
You can easily apply Gel Stain with a foam Brush. Lightly sand the surface with 180 grit sandpaper then apply very thin coats of the gel stain allowing at least 2 hours of dry time between coats. Each coat of stain needs about 24 hours to dry so plan accordingly.
See the section above on applying gel stain on finished wood for more detailed instructions. Clean up gel stain spills with mineral spirits immediately while wet. If stain dries it will be very hard to clean off any surface clothes or carpet.